Victron Energy Phoenix Smart IP43 Charger 12V 30A 1+1 PSC123051095
Technical Specification
Customer Rating | Not Available |
Brand | Victron |
Charge Voltage | 12 V |
Charge Rate | 30 A |
Guarantee | 5 Years |
Description
Victron Smart IP43 Charger (PSC123051095).
Victron Energy can trace its history as far back as 1975 and have become worldwide giants in the industry. Now based in the Netherlands they continue to be industry leaders that others look up to. Victron Energy has a strong, unrivalled reputation for technical innovation, reliability, and build quality with a vast product range of sinewave inverters, sinewave inverters/chargers, battery chargers, DC/DC converters, transfer switches, battery monitors and much more. Victron Energy's products can be found in the leisure, marine, automotive, industrial, solar, telecommunications sectors and more!
Smart IP43 Charger With boat owners in mind this adaptive 5-step charger can provide either 30A or 50A of charge to each of three battery banks. Or the charger 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. 24V models are available with 16A/25A charge. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features – see the datasheet below.
Features
Bluetooth Smart built-in
The wireless solution to set-up, monitor, control, update and synchronise Smart IP43 Chargers.
Smart IP43 Charger (1+1): two outputs to charge 2 battery banks
The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery.
Smart IP43 Charger (3): three full current outputs to charge 3 battery banks
Each output can supply the full rated output current. But the total of the 3 outputs combined can never exceed the current rating of the charger.
Automatic voltage compensation
The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.
Adaptive 6-stage charge algorithm: bulk– absorption – recondition – float – storage – refresh
The Smart IP43 Charger features our well-known “adaptive” battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.
The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.
Preventing damage due to excessive gassing: the BatterySafe mode
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
Less maintenance and ageing when the battery is not in use: the Storage Mode
The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalise’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.
Also charges Li-ion (LiFePO) batteries
Charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on-off port. Alternatively full control of voltage and current can be achieved with Bluetooth.
Fully programmable charge algorithm
The charge algorithm can be programmed with help of Bluetooth or the VE. Direct interface. Three preprogrammed algorithms can be selected with the mode button (see specifications on data sheet).
Optional external battery voltage and temperature sensing via Bluetooth
A Smart Battery Sense, SmartShunt or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more Smart IP43 Chargers via VE.Smart Networking.
Remote on-off
The remote on/off consists of two terminals: Remote H and Remote L. A remote on/off switch or relay contact can be connected between H and L. Alternatively, terminal H can be pulled high, or terminal L can be pulled low. See manual for details.
***Please refer to the Data Sheet or Manual for specific specifications
Ask A QuestionQuestions and Answers
There are currently no customer questions, please use the link above to ask your question.