Contact Us via Whatsapp
01745 823399
Trustpilot rated Excellent PayPal Accepted ApplePay Accepted

Victron Energy Skylla IP44 12/60 (1) Battery Charger 12V 60A SKY012060000

Victron Energy Skylla IP44 12/60 (1) Battery Charger 12V 60A SKY012060000

£ 749.49 inc. VATPrice

£ 7.99 inc. VATStandard Delivery

In Stock


Click and Collect


Technical Specification

BrandVictron
Product CodeSKY012060000
RangeVictron Skylla
Charge Voltage12 V
Charge Rate60 A
Length265 mm
Width375 mm
Height inc. terms401 mm
Guarantee5 Years

Description

Victron Energy Skylla IP44 12V 60A Charger (1) (SKY012060000).

Victron Energy can trace its history as far back as 1975 and have become worldwide giants in the industry. Now based in the Netherlands they continue to be industry leaders that others look up to. Victron Energy has a strong, unrivalled reputation for technical innovation, reliability, and build quality with a vast product range of sinewave inverters, sinewave inverters/chargers, battery chargers, DC/DC converters, transfer switches, battery monitors and much more. Victron Energy's products can be found in the leisure, marine, automotive, industrial, solar, telecommunications sectors and more!

The Skylla-IP44 Charger

Skylla-IP44 (1): one full rated output together with an isolated 3A trickle charge output for a starter battery

IP44 protection

Steel epoxy powder coated case and splash proof. Withstands the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.

LCD display

For status monitoring and to easily adapt the charge algorithm to a particular battery and its conditions of use. CAN bus interface (NMEA2000) To connect to a CAN bus network, to a Skylla-i Control panel or to the Color Control digital display.

Synchronised parallel operation

Several chargers can be connected in parallel and synchronised with the help of the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables.

The right amount of charge for a lead-acid battery: variable absorption time

When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged.

Preventing damage due to excessive gassing: the BatterySafe mode

If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-IP44 will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.

Less maintenance and ageing when the battery is not in use: the Storage mode

The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (26,4V for 24V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

To increase battery life: temperature compensation

Every Skylla-IP44 comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.

Battery voltage sense

In order to compensate for voltage loss due to cable resistance, the Skylla-IP44 is provided with a voltage sense facility so that the battery always receives the correct charge voltage.

Use as a power supply

As a result of the excellent control circuit, the Skylla-IP44 can be used as a power supply with perfectly stabilised output voltage if batteries or large buffer capacitors are not available.

Li-Ion (LiFePO4) ready

Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the CAN bus port.


***Please refer to the Data Sheet or Manual for specific specifications

Ask A QuestionQuestions and Answers

There are currently no customer questions, please use the link above to ask your question.